K.N.Toosi U. of Tech.

Faculty of Electrical Engineering

 

Department of Electric Power Systems

 
Karim Abbaszadeh
Professor
Office: Elec. Eng. Dep. K. N. University, Seyed Khandan, Shariaty Str.

P.O.BOX: 16315-1355 Tehran, Iran

Phone Number: +98 (21) -84062324
FAX Number: 21-84062066
E-mail Address: Abbaszadeh@kntu.ac.ir
Books
Finite Element Analyses of Electrical Machine (in Persian)

 

Power Electronic Dc-Dc & Dc-Ac Coverter, (in Persian), K.N.Toosi University of Technology, 2015

 

Journal Papers
  1. R.Nasiri-Zarandi , Ag. Ghaheri, K.Abbaszadeh, "Thermal Modeling and Analysis of a Novel Transverse Flux HAPM Generator for Small Scale Wind Turbine Application" To be Accepeted in IEEE Transactions on Energy Conversion, Article in press 2019
  2. A.Mohammadi Ajamloo; K.Abbaszadeh; R. Nasiri-Zarand, "A Novel Transverse Flux Permanent Magnet Generator for Small-Scale Direct Drive Wind Turbine Application: Design and Analysis", International Journal of science and technology (Scientia Iranica) Articles in Press, Accepted Manuscript , Available Online from 22 July 2019
  3. S Hajiaghasi, K.Abbaszadeh, A Salemnia, "A New Approach for Transformer Interturn Faults Detection Using Vibration Frequency Analysis" Iranian. J. Electr. Electron. Eng 15 (1), 14-28, 2019
  4. M. Jafari, K.Abbaszadeh, "A novel DTC-SVM approach for two parallel-connected induction motors fed by matrix converter" Turkish Journal of Electrical Engineering and Computer Sciences, 2018,
  5. K.Abbaszadeh, S.Ebrahimi, "Modelling, Simulation & Blade Pitch Fault Detection of Wind Turbines Equipped with permanent Magnet Synchronous Generator Based-on Support Vector Machine" Vol 10, N01, Spring 2016, Journal of Control, Iran
  6. Peyman Saadat, K.Abbaszadeh, "A Single Switch High Step up DC-DC Converter Based on Quadratic Boost", To be accepted in IEEE Tran. On Industrial Electronic.
  7. Ahmad Reza Naderi, K.Abbaszadeh," A Novel High Step-up DC-DC Converter with Input Current Ripple Cancelation", To be accepted in IET Power Electronics.
  8. Ajily, Ehsan. Ardebili, Mohammad; K.Abbaszadeh,"Magnet Defect and Rotor Eccentricity Modeling in Axial Flux Permanent Magnet Machines via 3D Field Reconstruction Method Conformal Mapping Method", To be Accepeted in IEEE Transactions on Energy Conversion
  9. K.Abbaszadeh, F. Saffar,"Modelling & Analyses of electromagnetic forces in distribution transformer under healthy and faulty condition",to be accepted in Journal of IAEEE.
  10. K.Abbaszadeh and Farhad Rezaee Alam, "On-Load Field Component Separation in Surface Mounted Permanent Magnet Motors using an Improved Conformal Mapping Method", IEEE Transactions on Magnetics, (Volume:PP , Issue: 99 ), 2015
  11. Farhad Rezaee Alam and K.Abbaszadeh,"Magnetic Field Analysis in Eccentric Surface-Mounted Permanent-Magnet Motors Using an Improved Conformal Mapping Method", IEEE Transactions on Energy Conversion, (Volume:PP , Issue: 99 ) Digital Object Identifier 10.1109/TEC.2015.2479562, 2015
  12. K.Abbaszadeh, A. Rahimi ,"Analytical Quasi 3D Modeling of an Axial Flux PM Motor with Static Eccentricity Fault ",International Journal of Science and Technology (Scientica iranica) Sharif Univ, 2015
  13. Mohammad Khalilzadeh, K.Abbaszadeh,"Non-isolated high step-up DC-DC converter based on coupled inductor with reduced voltage stress", IET Power Electronics, Volume 8, Issue 11, November 2015, p. 2184 - 2194 doi: 10.1049/iet-pel.2014.0899, 2014
  14. Seyede Sara Maroufian, K.Abbaszadeh, "Modeling and Fault Detection of an Axial Flux Permanent Magnet Motor Using Magnetic Equivalent Circuit and ARX Model",Journal of Control, Control and Instrumentation Engineers Association, Vol. 7, No. 4, winter 2013, pp. 9-18, 2013
  15. Farhad Rezaee Alama, K.Abbaszadeha & Amin Saieda,"Strand Current Distribution Modeling in Turbogenerators Using Finite-element Method Based on Proposed Dual Method", Electric Power Components and Systems,Taylor & Francis Group 43(2):134-145, 2015 , DOI: 10.1080/15325008.2014.973982 , 2015
  16. Housein Pardarnia, Salman Hajiaghasi, K.Abbaszadeh ,"Improved Structure of PNN Using PSA in Transformer Fault Diagnostic", Arab J Sci Eng. (39) 4845-4851 DOI: 10.1007/s 13369-014-1004-z, 2014
  17. H. Paydarnia, S.Hajiaghasi, K.Abbaszadeh, "A New Approach in Online Internal Fault Detection in Distribution Transformer via PCA Neural Network", Computational Intelligence in Elec. Eng. Journal, Vol. 5 , No.2 , summer 2015
  18. Ehsan Ajily, Member, IEEE, K.Abbaszadeh, and Mohammad Ardebili,"Three-Dimensional Field Reconstruction Method for Modeling Axial Flux Permanent Magnet Machines",IEEE Transactions on Energy Conversion, (Volume:30 , Issue: 1 ) Digital Object Identifier 10.1109/TEC.2014.2353299, Sep, 2014
  19. A.R. Edalatian, K.Abbaszadeh, "HARMONIC MINIMIZATION IN CASCADED H-BRIDGE MULTILEVEL INVERTER BY ICA", IJTPE Journal www.iotpe.com December 2013 Issue 17 Volume 5 Number 4 Pages 72-76
  20. K.Abbaszadeh, Seyedamin Saied, Siroos Hemmati, Alberto Tenconi,"Inverse transform method for magnet defect diagnosis in permanent magnet machines",IET Electric Power Applications, doi: 10.1049/iet-epa.2013.0176, 2013
  21. S. Saied1, K.Abbaszadeh, A. Tenconi3 and S. Vaschetto3,"New Approach to Cogging Torque Simulation Using Numerical Functions", IEEE Transactions on Industry Applications,DOI 10.1109/TIA.2013.2293814, 2013
  22. Akbar Tohidi, Ali Shamsaddinlou, Oveis Abedinia, Ali Khaki Sedigh, K.Abbaszadeh, "New Practical Design of Disturbance Rejection Control Scheme for DFIG with Wind Energy Conversion Systems",International Review of electrical Engineering (IREE) Vol 8, No 3, 2013
  23. Sara Laali1, K.Abbaszadeh, Hamid Lesani,"Control of Asymmetric Cascaded Multilevel inverters Based On Charge Balance Control Methods",International Review of Electrical Engineering - April 2011 (Vol. 6 N. 2) - Papers Part A
  24. K.Abbaszadeh, F. Rezaee Alam , M. Teshnehlab,"Slot opening optimization of surface mounted permanent magnet motor for cogging torque reduction",Energy Conversion and Management 55 (2012) 108-115, 2012
  25. K.Abbaszadeh , F. Rezaee Alam, S.A. Saied,"Cogging torque optimization in surface-mounted permanent-magnet motors by using design of experiment", Energy Conversion and Management 52 (2011) 3075-3082, 2011
  26. K.Abbaszadeh , Farhad Rezaee Alam,"Circulating current analysis between strands in armature winding of a turbo-generator using analytical model",Turk J Elec Eng & Comp Sci (2013) 21: 55 { 70c TUBI_TAK doi:10.3906/elk-1105-36, 2013
  27. K.Abbaszadeh, S.Roozbehani,"A New Approach for Maximum Power Extraction from Wind Turbine Driven by Doubly Fed Induction Generator Based on Sliding Mode Control",Energy management Journal No.2 Winter 2011, pp.11-22, 2012
  28. F. Tootoonchian, K.Abbaszadeh and M. Ardebili,"New Technique for Analysis of Static Eccentricity in Axial Flux Resolver", MEASUREMENT SCIENCE REVIEW, Volume 12, No. 1, 2012
  29. Farid Tootonchiyan, Mohammad Ardebili, K.Abbaszadeh,"Dynamic Performance Prediction of an Axial Flux Resolver",PRZEGLAD ELEKTROTECHNICZNY (Electrical Review), ISSN 0033-2097, R. 88 NR 2, 2012
  30. Tootoonchian,F., Ardebili, M., K.Abbaszadeh,"Using average DC-Pulse response of stator current for identification of axial Flux Single-Phase rotary transformer parameters",Przeglad Elektrotechniczny , 88 ( 11 A ) pp. 142 - 145, 2012
  31. F.Tootoonchian, K.Abbaszadeh, M.Ardebili,"Novel axial flux brushless resolver analysis and optimization using 3D finite element and D-Q model method",Iranian Journal of Electrical & Electronic Engineering, Vol. 8, No. 3, Sep. 2012
  32. S.Jamali, K.Abbaszadeh,"The Study of Magnetic Flux Shunts Effects on the Leakage Reactance of Transformers via FEM" Majlesi Journal of Electrical Engineering, Vol. 4, No. 3, September 2010, pp 47-56.
  33. S.A.Saeed, K.Abbaszadeh, M.Fadaei, "Reduced Order Model of Developed Magnetic Equivalent Circuit in Electrical Machine Modeling" IEEE TRANSACTIONS ON MAGNETICS, VOL. 46, NO. 7, JULY 2010.
  34. K.Abbaszadeh, M.Ardebili, E.Sarani, "Modeling and Simulation Stator Fault in induction Motor by Magnetic Equivalent Circuit" to be Accepted in Fanni Journal.
  35. S.Jamali, K.Abbaszadeh, "Geometry Optimization of the Magnetic Shunt and Arrangement Influence on Axial Forces in Power Transformers Based on FEM Method"International Review on Modeling and Simulations Journal (IREMOS), ISSN 1974-9821, Vol. 2 No.5,Ocb 2009, pp 548-557
  36. K.Abbaszadeh, M.Ardebili, E.Sarani, "Modeling and Diagnosis of Stator winding Fault in Squirrel Cage Induction Motor", IJES Journal ISNN 1018-7375, Vol.19 No.10 A, 2009, pp 114-121
  37. S. Saied, K.Abbaszadeh,"Cogging Torque Reduction in BLDC & PMSM Motors Using Dual Structures" International Review on Modeling and Simulations, February 2009, Italy.
  38. S. Saied, K.Abbaszadeh, "Cogging Torque Reduction in Brushless DC Motors Using Slot-Opening Shift", Advances in Electrical and Computer Engineering, February 2009 Vol.9 No.1,Romania
  39. S.A.Gholamian, M. Ardebili K.Abbaszadeh, "Selecting and Construction of High Power Density Double-Sided Axial Flux Slotted Permanent Magnet Motors for Electric Vehicles", International Review of electrical engineering, June 2009, ISSN: 1827- 6660 Italy.
  40. S.A. Saied, K.Abbaszadeh, S.Hemmati, M.Fadaee, "New Approach to Cogging Torque Reduction in Surface-Mounted Permanent-Magnet Motors" Vol.26 No.4 U.K European Journal of Scientific Research.
  41. S.A.Gholamian, M. Ardebili, K.Abbaszadeh, "Effect of Air Gap on Torque Density for Non-Slotted Axial Flux TORUS and AFIR PM Motors " European Journal of Scientific Research, ISSN 0973-4562, Volume 20, Number 3, June (2008), pp:623-631
  42. S.A.Gholamian, M. Ardebili, K.Abbaszadeh, S.Mahmodi Charati, "Optimum Design of 1KW Axial Flux Permanent Magnet Slotted TORUS Motor" European Journal of Scientific Research, ISSN 0973-4562, Volume 20, Number 3, June (2008), pp:623-631
  43. S.A.Gholamian, M. Ardebili, K.Abbaszadeh, "Analytic and FEM Evaluation of Power Density for Various Types of Double-Sided Axial Flux Slotted PM Motors" International Journal of Applied Engineering Research, ISSN 0973-4562, Volume 3, Number 6 June (2008), pp:749-763
  44. F.Bagheri, H.Khaloozaded, K.Abbaszadeh, "Stator Fault Detection in Induction Machines by Parameter Estimation Using Adaptive Kalman Filter" Iranian Journal of Electrical & Electronic Engineering, Vol. 3, Nos. 3 & 4, July 2007.
  45. H.A. Toliyat, K.Abbaszadeh, M. Rahimian, and L.E. Olson, "Rail Defect Diagnosis using Wavelet Packet Decomposition" IEEE TRANSACTIONS OF INDUSTRY APPLICATIONS, VOL. 39, NO. 5, SEPTEMBER/OCTOBER 2003, pp 1454-1461.
  46. K.Abbaszadeh, J. Milimonfared, M. Menhaj, H.A. Toliyat "A new approach to broken rotor bar detection in squirrel cage induction motor via model-based parameter estimation", Amir Kabir Journal of Science & Technology, has been accepted at August 20, 2002.
  47. K.Abbaszadeh, J. Milimonfared, H.Vaez, " Stator Winding Fault Diagnostic in squirrel cage induction motor" Fanni Journal of science, Vol.35, No.4, Dec. 2002, pp 477-487
  48. K.Abbaszadeh, J. Milimonfared, H.Vaez, "Modeling and simulation of Stator Winding in squirrel cage induction motor" Fanni Journal of science, Vol.36, No.3, Dec. 2002, pp 310-297
  49. K.Abbaszadeh, E. Fallah, J. Milimonfared, et.al, "Modeling and Simulation of Dual Three-Phase Induction Machine Under Fault Conditions and Proposal of a new Vector Control Approach for Torque Oscillations Reduction", Scientia Iranica, Vol.9, No 4, pp 321-327
  50. K.Abbaszadeh, J. Milimonfared, H.A. Toliyat "Broken Bar Detection in Squirrel Cage Induction Motor via Wavelet Transformation" Iranian Journal Of Science & Technology, Shiraz University, Volume 27, Number B4, 2003, pp 763-770, ISSN 0363-1307
  51. J.Milimonfared, K.Abbaszadeh, M.Menhaj, H.Kazemy, " Estimation of Induction Motor Speed by E.K.F in Stationary Frame and Use of Rotor Flux and Study of Parameter Variation" Esteghlal Journal of Engineering, Isfahan University of Technology, Vol 18, No. 2 , March 2000, ISSN 1025-2851.
  52. J.Milimonfared, K.Abbaszadeh, M.E.Akbari, " Design and Impelementation of PWM Rectifiers in Order to Feed & Control Motor Speed and its Abilities to Use with E.P.W.M & S.P.W.M Methods ", Amir Kabir Journal of Science & Technology, Vol.11. No. 42, fall 1999, winter 2000, ISSN.1015-0951.
Conferene Papers
  1. A.Gholami, K.Abbaszadeh," A new two-input and multi-output Interleaved DC_DC boost converter for satellites power system" 10th Annual International Power Electronic Drives and Technology Conference PEDSTC 2019, Shiraz, Iran.
  2. M.Mahdavi, K.Abbaszadeh, M Hatami , "A Single Phase Boost Switched-Capacitor Multilevel Inverter Topology" 10th Annual International Power Electronic Drives and Technology Conference PEDSTC 2019, Shiraz, Iran.
  3. R.Nasiri-Zarandi, A.M Ajamloo, K.Abbaszadeh, "Proposing the Output Equations and 3-D MEC Modeling for U -Core TFPM Generators" International Symposium on Power Electronics, Electrical Drives Automation and Motion SPEEDAM 2018, Amalfi, Italy.
  4. R.Nasiri-Zarandi, A. Ghaheri, K.Abbaszadeh, "Cogging Torque Reduction in U-Core TFPM Generator Using Different Halbach-Array Structures" International Symposium on Power Electronics, Electrical Drives Automation and Motion SPEEDAM 2018, Amalfi, Italy.
  5. H.Soltani, K.Abbaszadeh, H.Sadegi, D.Abbas Moghadam, "A DC- DC converter with power factor correction for use in combined electrical systems" 33th international power system conference (PSC), 2018, Tehran, Iran.
  6. P.Mohammadi, A.A.Soratgar, K.Abbaszadeh, "Robust control of Z-source inverter" first international conference on the new achievements in electrical engineering and computer science, 2018, Tehran, Iran.
  7. A.R.Naderi, K.Abbaszadeh, "Applying an optimized switching strategy to a high gain boost converter for input current ripple cancellation" 8th Power Electronics, Drive Systems and Technologies Conference, PEDSTC 2017, Tehran, Iran.
  8. M.A.Norouzi, K.Abbaszadeh, A.Havanasian, "Transient improvements of a winding turbine with a soft startup in a standard IEEE 14 bus network" 4th Clean Energy Conference, 2017, Tehran , Iran.
  9. A.Mohammadzadeh, H.Yousefi, K.Abbaszadeh, "A Soft switching Dc-Dc converter for solar cell application" 5th National Conference on New Ideas in Electrical Engineering, 2018, Tehran, Iran.
  10. K.Abbaszadeh, H.Babaee, "Speed Control of the induction motor with DTC and predictive contrl"National Conference on Electrical Engineering Sciences, 2017, Tehran, Iran.
  11. K.Abbaszadeh, H. Yousefi, "Vector control of induction motor using matrix inverter and fuzzy controller" International Conference on Science and Engineering, 2017, Tehran, Iran.
  12. K.Abbaszadeh, F.R.Alam, The circulating current and internal fault analysis between strands in stator winding of a turbo generator using the analytical model"27th PSC conference , Dec 2012, Tehran, Iran
  13. K.Mehdizadegan, K.Abbaszadeh, "Output power smoothing of PMSG-based wind energy conversion system equipped with matrix converter " 7th Power Electronics, Drive Systems and Technologies Conference, PEDSTC 2016
  14. A. H. Zarei, K.Abbaszadeh, and Kiarash Safari The Analytical Analysis of the Rotor Losses in the PMSM Motors", World Congress on Engineering and Computer Science 2012, 24-26, October 2012, San Francisco, USA
  15. R.Ghassemi, , K.Abbaszadeh, "A simplified predictive current Controlled Cascaded H-Bridge Multilevel Inverter for grid-connected photovoltaic systems" 6th Annual International Power Electronics, Drive Systems, and Technologies Conference, PEDSTC 2015, Tehran, Iran.
  16. Khalilzadeh, M., Mahdipour, M., K.Abbaszadeh, "High step-up DC-DC converter based on three-winding coupled inductor" 6th Annual International Power Electronics, Drive Systems, and Technologies Conference, PEDSTC 2015, Tehran, Iran.
  17. S.Hajiaghasi, H. Paidarnia, K.Abbaszadeh" Analysis of Electromagnetic Forces in Distribution Transformers Under Various Internal Short-Circuit Fault", Regional Cired Conference 2013, Tehran, Iran
  18. S.Z. Mousavi, K.Abbaszadeh, A.Azimi, "LQR Control of DFIG Wind Generator Maximum power point tracking"27th PSC conference , Dec 2012, Tehran, Iran
  19. K.Abbaszadeh ,S. S.Maroufian "Axial Flux Permanent Magnet Motor Modeling using Magnetic Equivalent Circuit"Electrical Engineering (ICEE ), 2013 21st Iranian Conference, 2013 Page(s): 1 - 6
  20. K.Abbaszadeh S. S.Maroufian, PM Demagnetization Detection in Axial Flux Permanent Magnet Motor using ARX Model Electrical Engineering (ICEE), 2013 21st Iranian Conference on, 2013 Page(s): 1 - 6
  21. K.Abbaszadeh , S. S.Maroufian, Design and Torque Optimization of a PM Synchronous Motor, Using an Auxiliary Winding' PDESTC 2014
  22. N. Bolouki, K.Abbaszadeh"Second Order Sliding Mode Control Of Permanent-Magnet Synchronous Wind Generator For Direct Active and Reactive Power control"PDESTC 2014
  23. N. Bolouki, K.Abbaszadeh , "Input-Output linearization Of Wind Energy System Based on PMSG For Direct Active And Reactive Power Control Via Sliding Mode Approach"International Conference and Exihibition on Green Energy for Sustainable Development (ICUE 2014)
  24. F. Tootoonchian, K.Abbaszadeh, M.Ardebili, "Optimum Desgin of New Reluctance Position sensor with Robost Static Eccentrisity"2nd International Conference on Control, Instrumentation, and Automation (ICCIA), 27 Dec. 2011,Shiraz, Iran
  25. F. Tootoonchian, M.Ardebili, K.Abbaszadeh, "Energy Consumption Measuring in City Bike Driving Cycle by using Resolver"1nd international Conference of City Bike, 19 Oct. 2010 Tehran Iran,
  26. K.Abbaszadeh, F.R.Alam, "Analytical Modeling and Analyses of Circulating Current in Armiture Winding of Synchronouse Generator"4th Electric Power Generation Conference, Feb. 2012, Tehran , Iran
  27. S. Roozbehani, K.Abbaszadeh, M.Torabi, "Sensorless Maximum Wind Energy Capture Based on Input Output Linearization and Sliding Mode Control"IET Renewable Power Generation Conference 2011, 6 - 8 Sep. 2011, Edinburgh, UK
  28. S.Laali, K.Abbaszadeh, H.Lesani, "New Hybrid Control Methods Based on Multi-Carrier PWM Techniques and Charge Balance Control Methods for Cascaded Multilevel Converter"24th Canadian Conference on Electrical and Computer Engineering (CCECE), 2011
  29. S. Saied, K.Abbaszadeh,A.Tenconi, S.Vaschetto, "New Aapproach to Cogging Torque Simulation Using Numerical Functions"IEEE International Electric Machines and Drives Conference, IEMDC 2011
  30. M. H. Karimi, H. Zamani, K.Abbaszadeh, S. Hemmati DSP-based Optimal Sensor-Less Vector Control Drive for Axial-Flux PM motor"Proceedings of the 2011 International Conference on Power Engineering, Energy and Electrical Drives, Torremolinos (Malaga), Spain. May 2011
  31. K.Abbaszadeh, H.Samadzadeh, "A Transformer Dc-Dc Converter with Improved High Step up Voltage Gain and Lower Voltage Stress on Active Switches"7th International Conference on Electrical and Physical Problems of Power Engineering, 7-9 July 2011, Lefkosa,Tr Northern Cyprus, pp:1-5
  32. S.Saied, K.Abbaszadeh, A.Tenconi, "Improvement to Winding Function Theory for PM Machine Analysis"Proceedings of the 2011 International Conference on Power Engineering, Energy and Electrical Drives, Torremolinos (Malaga), Spain. May 2011.
  33. K.Abbaszadeh M. Jafari, "Optimizing Cogging Torque Reduction with Slot Opening Shift Method in PM Motor by RSM"Power Electronic Drive Systems Technologies Conference (PEDSTC 2011) 17-18 Feb 2011 Tehran, Iran.
  34. K.Abbaszadeh, M.Zakery, "Phase to phase and phase to earth fault Diagnosis in electrical distribution networks using radio waves"25th international power system conference 2010 (PSC 2010), Page(s): 1-7
  35. S.Roozbehani, A.Tohidi, A.K.Sedigh, K.Abbaszadeh, "New method to maximum power extraction in wind turbine equipped with DFIG using sliding mode control"25th international power system conference 2010 (PSC 2010), Page(s): 1-7
  36. Laali, S., K.Abbaszadeh, Lesani, H. "Development of multi-carrier PWM technique for multilevel inverters"International Conference on Electrical Machines and Systems (ICEMS), 2010 ,Page(s): 77 - 81
  37. S.Laali, K.Abbaszadeh, H.Lesani, "A new algorithm to determine the magnitudes of dc voltage sources in asymmetric cascaded multilevel converters capable of using charge balance control methods" International Conference on Electrical Machines and Systems (ICEMS), 2010 Page(s): 56 - 61
  38. M.Rahimi; M.Momeni,; K.Abbaszadeh, " A new approach to minimize torque pulsations in PMSM driven by field oriented control"International Symposium on Power Electronics Electrical Drives Automation and Motion (SPEEDAM), 2010 Page(s): 490 - 494
  39. K.Abbaszadeh,; Yazdaninejad, M, "A modified topology of isolated interleaved flyback boost converter with Winding-Cross-Coupled inductors" International Symposium on Power Electronics Electrical Drives Automation and Motion (SPEEDAM), 2010 , Page(s): 1325 - 1330
  40. K.Abbaszadeh , M.Ardebili, A. R. Alaei, "Fully Electronic Tap-Changer with Triac Switch: Simulation and Practical Results", Power Electronic Drive Systems Technologies Conference (PEDSTC 2010) 17-18 Feb 2010 Tehran, Iran
  41. M. Rahimi, K.Abbaszadeh. M. Jafari A. Radan, "Torque Ripple suppression of Surface Mounted Permanent Magnet Synchronous Motor Using Harmonic Injected Currents"Power Electronic Drive Systems Technologies Conference (PEDSTC 2010) 17-18 Feb 2010 Tehran, Iran
  42. N. Abbasi, K.Abbaszadeh, "Influence of Nonsinusoidal Flux Waveform on Transformer Design Methodology" Power Electronic Drive Systems Technologies Conference (PEDSTC 2010) 17-18 Feb 2010 Tehran, Iran
  43. K.Abbaszadeh, M.Jafari, M.Ardebili, "Magnetic Equivalent Circuit Modeling of Slot Less Axial Flux PM Motor ICEE2009, Tehran Iran, May 2009
  44. K.Abbaszadeh, M. Mohammadi, M.Ardebili, Miralikhani, " Coupled Electromagnetic-Thermal Finite-Element Modeling of Cast-Resin Dry-Type Transformers, ICEE2009, Tehran Iran, May 2009
  45. Saied M. Karrari, K.Abbaszadeh, and O.P. Malik, "Identification of Electric Parameters of Synchronous Generators with Detailed Representation of Damper Windings"NORTH AMERICAN POWER SYMPOSIUM, Sept 28th to 30th, 2008
  46. M.Fazli, N.Talebi, K.Abbaszadeh, "New method for providing uninterrupted performance wind turbine equipped to DFIG during the malnutrition and short circuit condition in the network using STATCOM"24th international power system conference 2009 (PSC 2009), Page(s): 1-7
  47. K.Abbaszadeh, S.Jamali, M.Ardewbili, "Leakage Reactance and flux distribution calculation and Analyses in power transformer using finite element method" 24th international power system conference 2009 (PSC 2009
  48. A.Mosavi, M.Mohammadi, K.Alikhani, K.Abbaszadeh, "Power losses calculation in Resin type dry power transformer using FEM Listen"24th international power system conference 2009 (PSC 2009),
  49. Steady state parameters extraction and inrush current estimation in power transformer with considering of core saturation effect
  50. S.A.Gholamian, M. Ardebili, K.Abbaszadeh, "Design optimization of a Double Side Axial PM Motor by Genetic Algorithm"Proceedings of the 16th ICEE2008 Conference,13-15 May, 2008, Tehran, Iran
  51. S.A.Gholamian, M. Ardebili, K.Abbaszadeh, "Density Comparison for Double-Sided Axial Flux Slotted TORUS and AFIR PM Motors", Proceedings of the 16th ICEE2008 Conference,13-15 May, 2008, Tehran, Iran
  52. A.Gholamian, M. Ardebili, K.Abbaszadeh, "Power density comparison for various types of non-slotted double-sided axial flux PM motors"Proceedings of the 6th ICEENG Conference, 27-29 May, 2008 Cairo, Egypt
  53. S.A.Gholamian, M. Ardebili , K.Abbaszadeh" Effect of air gap on torque density for double-sided TORUS and AFIR slotted PM motors" Proceedings of the 6th ICEENG Conference, 27-29 May, 2008, Cairo, Egypt
  54. F.Bagheri, H.Khaloozaded, K.Abbaszadeh, "Stator Fault Detection in Induction Machines by Parameter Estimation, Using Adaptive Kalman Filter"15th Mediterranean Conference on Control & Automation (Med2007), Jul 27-29 2007, Athens, Greece.
  55. R. Alaei, K.Abbaszadeh , M. Ardebili, "Design and Built of on - Load Fully Electronic Tap-Changer with Triac Switch: Simulation and Practical Results"17th International Conference on Electrical Machines, September 2-5, 2006, Greece
  56. M. J. Rastegar, A. A. Suratgar, K.Abbaszadeh, M.H.Tosifian, "A New Based-Carrier Pulse-Width Modulation of Z-Source Inverters"ICEMS2006, Tokyo, Japan
  57. K.Abbaszadeh, S.A Gholamian1, M. Ardebili1, and Hamid A. Toliyat, "Modeling of B-H Loop for Core Loss Calculations in Power Transformer Using Finite Element Method"12th Biennial IEEE Conference on Electromagnetic Field Computation CEFC 2006, Miami, FL USA - April 30th - May 3rd 2006
  58. M. Ardebili, K.Abbaszadeh, S. Jamali, and H. Toliyat "Winding Arrangement Effects on Electromagnetic Forces and Short-Circuit Reactance Calculation in Power Transformers via Numerical and Analytical Methods"12th Biennial IEEE Conference on Electromagnetic Field Computation CEFC 2006, Miami, FL USA - April 30th - May 3rd 2006
  59. M. Allahbakhshi, K.Abbaszadeh, A. Akbari, "Effect of Asymmetrical Dimensions in Short Circuit Forces of Power Transformers"International Conference on Electric Machinary (ICEMS) Sep. 2005, Nanjin, China
  60. S. Jamali M. Ardebili, K.Abbaszadeh, "Calculation of Short Circuit Reactance and Electromagnetic Forces in Three Phase Transformer by Finite Element Method"International Conference on Electric Machinary (ICEMS) Sep. 2005, Nanjin, China
  61. E. Sarani, K.Abbaszadeh, M.Ardebili, "Modeling and Simulation of Turn-Fault and Unbalance Magnetic Pull in Induction Motor Based on Magnetic Equivalent Circuit Method"International Conference on Electric Machinary (ICEMS) Sep. 2005, Nanjin, China
  62. Mehdi Arehpanahi, Jafar Mili Monfared, K.Abbaszadeh, "Sensorless Fuzzy Logic Soft Start of Induction Motor with Load Detection" International Conference on Electric Machinary (ICEMS) Sep. 2005, Nanjin, China
  63. E. Sarani, K.Abbaszadeh, M.Ardebili "Modeling and Simulation of Inter Turn Short Fault in Stator Winding of Induction Motor via Magnetic Equivalent Circuit (MEC"13th International Conference on Electrical Engineering, Zanjan, IRAN, May. 29, 2005.
  64. M. Arehpanahi, J.Monfared, K.Abbaszadeh, "Design and Implementation of Induction Motor Soft Start Drive for Energy Efficiency Improving in Light Load", 13th International Conference on Electrical Engineering, Zanjan, IRAN, May. 29, 2005.
  65. K.Abbaszadeh, J. Milimonfared, et.al, "Broken Bar Detection In Induction Motor Via Wavelet Transformation"27th Annual Conference of the IEEE Industrial Electronic Society, Nov. 29, Denever Colorado USA, pp 95-100
  66. K.Abbaszadeh, M. Rahimian, H. A. Toliyat, L. E. Olson, "Rail Defect Diagnosis using Wavelet Packet Decomposition"IEEE Industry Applications Society 37th Conference, Pittsburgh Pennsylvania USA,October 13-8,2002
  67. J.Millimonfared, M.Arehpanahi, K.Abbaszadeh, "Sensorless Fuzzy Logic Soft Start of Induction Motor with Load Detection"International Conference on Control, Automation and Systems, Gyeongiu, Korea (ICCAS 2003)
  68. J.Millimonfared, M.Arehpanahi, K.Abbaszadeh, "Efficiency Improving of Three Phase Induction motor in light load by AC-AC converter"the 18th international conference on power system, Tehran Iran.
  69. J.Milimonfared, M.B.Menhaj, K.Abbaszadeh, H.Kazemy, " A New Approach for Torque Oscillation Reducing in Senseless Vector Control of Induction Motors"6th International Conference on Electric and Electrical Engineer, Iran.
  70. K.Abbaszadeh, J.Milimonfared, A.Rahimi, "Analysis and Simulation of Ac-Dc Converter with Unity Power Factor for Control of Dc Motors". 6th International Conference on Electric and Electrical Engineer, Iran.
  71. M.B.Menhaj, K.Abbaszadeh, J.Milimonfared, "Torque Adjustment and Switching Reduction by Fuzzy Logic in Senseless Vector Control of Induction Motors". 6th European Congress on Intelligent Techniques & Soft Computing, Aachen Germany, September 7-10, 1998 Vol. 2. pp 924 -928.
  72. J.Milimofared, K.Abbaszadeh, E.Fallah, "Propose a New R.F.O Vector Control of Dual Three Phase Induction Machine in Normal and Faulty Mode", 8th International Conference on Electric and Electrical Engineer, Iran.
  73. J.Milimofared, K.Abbaszadeh, E.Fallah, " Modeling and Simulation of Dual Three Phase Induction Machine in Fault Condition (Two Phase Cut Off) and Propose A New R.F.O Vector Control Approach for Torque Oscillation Reducing in Fault Mode". ICEM 2000, 26-30 August 2000, Helsinki Finland.